CEETSS-0022 Stigagrindur fyrir bíla og vörubíla
“
Vörulýsing
- Material: Stainless Steel or Aluminum Alloy
- Mounting Hardware: M8 hex bolts, M8 flat washers
- Uppsetning: Mælt er með faglegri uppsetningu
- Torque: 15 ft-lbs
Notkunarleiðbeiningar fyrir vöru
Fyrir uppsetningu
Lestu leiðbeiningarnar vandlega áður en þú byrjar að setja upp.
Ensure you have the proper tools for a quality installation. If any
missing parts or damage is found, take a picture and contact us.
Professional installation is highly recommended. Periodically check
to ensure all mounting hardware remains secure and tight.
Skref 1
- Finndu (4) uppsetningarstöður á hvorri hlið.
- Fjarlægðu gúmmítappana á innra vippborðinu.
- Clean the sealant and dirt around the mounting positions.
Skref 2
- Attach the bracket to the inner rocker panel and secure with
(2) M8 hex bolts and (2) M8 flat washers. - Repeat to install the remaining brackets, but do not fully
herða.
Skref 3
- Remove (8) M8 hex bolts and (8) M8 flat washers from the step
bar. - Renndu uppsetningarsporunum í rétta stöðu.
- Með aðstoð, lyftu og festu þrepstöngina við festingar.
- Secure the step bar on brackets with (8) M8 hex bolts and (8)
M8 flat washers. - Repeat to install the other side step bar but do not fully
herða.
Skref 4
- Tighten M8 hex bolts and nuts on the vehicle with 15 ft-lbs
tog. - Adjust the step bar to be level and tighten M8 hex bolts with
15 ft-lbs torque. - After installation, periodically check to ensure all mounting
vélbúnaðurinn helst öruggur og þéttur.
Algengar spurningar (algengar spurningar)
Sp.: Hvað ætti ég að gera ef ég finn vantar hluti eða skemmdir á meðan
uppsetningu?
A: Take a picture of the issue and contact us for assistance. Do
not proceed with installation if parts are missing or damaged.
Q: Can I install the step bar without professional help?
A: Þó að mælt sé með faglegri uppsetningu geturðu það
follow the provided instructions carefully for self-installation.
Ensure to check all mounting hardware periodically for
öryggi.
“`
Fyrir uppsetningu
Read this instruction carefully before starting installation. Proper tools will improve the quality of installation and reduce the time required. If missing parts or any damage found, please take a picture and contact us. Professional installation would be highly recommended. Periodic check to ensure all mounting hardware remains secure and tight.
Skref 1
1. Locate (4) mounting positions each side. 2. Remove the rubber plugs on the inner rocker panel. 3. Clean the sealant and dirt around mounting positions.
Skref 2
1. Attach the bracket to the inner rocker panel and secure with (2) M8 hex bolts, (2) M8 flat washers.
2. Repeat to install remaining brackets, do not fully tighten.
Driver Side Crew Cab
Framan
Driver Side Crew Cab
Framan
-1-
-2-
Skref 3
1. Remove (8) M8 hex bolts and (8) M8 flat washers from the step bar. 2. Slide mounting tracks to proper positions. 3. With assistance, lift and attach the step bar to brackets.
Secure the step bar on brackets with (8) M8 hex bolts and (8) M8 flat washers. 4. Repeat to install the other side step bar
do not fully tighten.
Stainless Steel Step Bar
Aluminum Alloy Step Bar
Skref 4
1. Tighten M8 hex bolts and nuts on vehicle with 15 ft-lbs. torque. 2. Adjust the step bar to level and tighten M8 hex bolts with 15 ft-lbs. torque. 3. After the step bar installed
reglubundið eftirlit til að tryggja allan festingarbúnað
helst öruggur og þéttur.
Hlutalisti
Qty. Description ×8 Mounting Bracket ×16 M8 Hexagon Bolt ×16 M8 Flat Washer ×16 M8 Hexagon Nut
Pre-installed on Step Bar ×16 M8 Hexagon Bolt ×16 M8 Flat Washer
Driver Side Crew Cab
-3-
Framan
-4-
Skjöl / auðlindir
 |
Afmerkja CEETSS-0022 þrepastig fyrir bíla og vörubíla [pdfUppsetningarleiðbeiningar CEETSS-0022, 3004, 3005, 3014, CEETSS-0022 Step Bar Car and Truck Running Boards, CEETSS-0022, Step Bar Car and Truck Running Boards, and Truck Running Boards, Truck Running Boards, Running Boards |