Tascam US-144MKII USB Audio Interface User Manual

Inngangur

This manual provides essential information for the proper setup, operation, and maintenance of your Tascam US-144MKII USB Audio Interface. The US-144MKII is a compact, bus-powered USB 2.0 audio/MIDI interface designed for high-quality recording on Mac and Windows computers. It offers two microphone inputs with phantom power, two line inputs, a switchable guitar input, MIDI I/O, and S/PDIF digital audio I/O, supporting up to 96kHz/24-bit audio resolution.

Vinsamlegast lesið þessa handbók vandlega áður en tækið er notað til að tryggja örugga og bestu mögulegu virkni.

Öryggisupplýsingar

Always observe the following safety precautions to prevent electric shock, short circuit, damages, fire, or other hazards.

• Do not open the unit or attempt to disassemble the internal parts or modify them in any way.
• Ekki láta tækið verða fyrir rigningu, notaðu það nálægt vatni eða í damp eða blautar aðstæður, eða settu ílát á það sem innihalda vökva sem gæti lekið inn í hvaða op sem er.
• If the USB cable becomes frayed or damaged, or if the unit is dropped or damaged, disconnect the USB cable immediately and have the unit inspected by qualified service personnel.
• Do not place the unit in a location where it may be exposed to excessive dust, vibrations, extreme cold or heat, or direct sunlight.
• Tryggið góða loftræstingu í kringum tækið meðan það er í notkun.

Innihald pakka

Staðfestu að pakkinn þinn inniheldur eftirfarandi hluti:

• Tascam US-144MKII USB Audio Interface unit
• USB 2.0 snúra
• Installation CD (for drivers and bundled software like Steinberg Cubase LE4)
• Notendahandbók (þetta skjal)

Vara lokiðview

Framhlið

The front panel of the US-144MKII features all primary controls and input jacks for easy access during recording and monitoring.

• INPUT hnappur: Stillir inntaksstyrk fyrir hljóðnema- og línuinntök.
• MON MIX Knob: Blends the direct input signal with the computer playback signal for zero-latency monitoring.
• LINE OUT Knob: Controls the output level to your studio monitors.
• PHONES hnappur: Stillir útgangsstyrk heyrnartólanna.
• MONO rofi: Sums the stereo input signal to mono for monitoring.
• MIC/LINE Inputs (L/R): XLR/TRS combo jacks for connecting microphones or line-level instruments.
• PHANTOM Power Switch: Virkjar +48V fantomafl fyrir þéttihljóðnema.
• SIG/OL Indicators: Lights green when a signal is present, red when the input is overloading.
• LINE/GUITAR IN (R): 1/4-inch input for line-level or high-impedance guitar/bass signals.

Bakhlið

The rear panel provides various connectivity options for your studio setup.

• LÍNA ÚT (V/H): RCA outputs for connecting to powered studio monitors or an amplíflegri.
• MIDI INN/ÚT: 5-pin DIN connectors for connecting MIDI devices such as keyboards or drum machines.
• DIGITAL IN/OUT (S/PDIF): Coaxial RCA connectors for digital audio input and output.
• USB tengi: Connects the interface to your computer for data transfer and power.

Uppsetning

Uppsetning bílstjóri

Before connecting the US-144MKII to your computer, it is crucial to install the latest drivers. The included CD may contain outdated drivers. For optimal performance and compatibility, always download the most current drivers directly from the official Tascam website. This ensures proper functionality and avoids potential issues, especially with newer operating systems.

1. Visit the official Tascam support websíða.
2. Locate the support page for the US-144MKII.
3. Download the appropriate driver for your operating system (Windows or macOS).
4. Follow the on-screen instructions to install the driver. Do not connect the US-144MKII until prompted by the installer, or until the installation is complete.

Að tengja viðmótið

1. Connect the US-144MKII to your computer using the supplied USB 2.0 cable. The unit is bus-powered, so no external power adapter is required.
2. Tengdu hljóðnemana þína við MIC/LINE Inputs (L/R) using XLR cables. If using condenser microphones, ensure the PHANTOM Power switch is engaged.
3. Connect line-level instruments (e.g., synthesizers) to the MIC/LINE Inputs (L/R) using 1/4-inch TRS cables, or a guitar/bass to the LINE/GUITAR IN (R).
4. Connect your studio monitors to the LINE OUT (L/R) RCA tjakkar.
5. Connect headphones to the 1/4-inch headphone jack on the front panel.
6. If using MIDI devices, connect them to the MIDI IN / OUT hafnir.

Í rekstri

Basic Recording Workflow

1. Kveikt á: Connect the US-144MKII to your computer via USB. The unit will power on automatically.
2. Hugbúnaðaruppsetning: Open your Digital Audio Workstation (DAW) software (e.g., Cubase LE4, included). Go to the audio settings/preferences and select the Tascam US-144MKII as your audio input and output device.
3. Aðlögun inntaksstyrks: Connect your microphone or instrument. Speak into the microphone or play your instrument at the loudest expected level. Adjust the INNSLAG hnappur þar til SIG/OL indicator lights green consistently, only occasionally flashing red on peaks. Avoid constant red illumination, which indicates clipping.
4. Eftirlit:
   • For zero-latency monitoring, adjust the MON MIX knob. Turning it towards "INPUT" increases the direct signal from your microphone/instrument, while turning it towards "COMPUTER" increases the playback from your DAW. Find a balance that allows you to hear both clearly without delay.
   • Adjust your headphone volume using the SÍMI knob and monitor speaker volume using the LÍNA ÚT hnappur.
5. Upptaka: Create a new audio track in your DAW, select the appropriate input (e.g., Input 1 for Mic L), and arm the track for recording. Press record in your DAW to begin.

Að nota Phantom Power

If you are using a condenser microphone, it requires +48V phantom power. Ensure the microphone is connected before activating phantom power. Press the PHANTOM power switch on the front panel. The corresponding LED will illuminate. Always disengage phantom power before disconnecting condenser microphones.

MIDI tengimöguleikar

The US-144MKII includes MIDI In and Out ports. Connect your MIDI keyboard, controller, or other MIDI devices to these ports. Your DAW software will recognize the US-144MKII as a MIDI interface, allowing you to send and receive MIDI data for controlling virtual instruments or external hardware.

Viðhald

• Þrif: Notið mjúkan, þurran klút til að þurrka ytra byrði tækisins. Notið ekki slípiefni, vax eða leysiefni.
• Geymsla: When not in use for extended periods, disconnect the USB cable and store the unit in a clean, dry place away from extreme temperatures.
• Kapalumhirða: Avoid bending or crimping USB and audio cables excessively. Store them neatly to prevent damage.

Úrræðaleit

• No Sound/Device Not Recognized:
  • Ensure the latest drivers are installed from the Tascam websíða.
  • Verify the USB cable is securely connected to both the interface and the computer. Try a different USB port or cable.
  • Check your computer's sound settings and your DAW's audio preferences to ensure the US-144MKII is selected as the input/output device.
  • Restart your computer and the interface.
• Latency Issues (Delay in Monitoring):
  • Notaðu MON MIX knob for zero-latency hardware monitoring.
  • In your DAW, reduce the buffer size in the audio settings. Lower buffer sizes reduce latency but require more CPU power.
  • Ensure your computer meets the minimum system requirements for your DAW and the interface.
• Noisy Sound/Interference:
  • Athugið allar kapaltengingar til að tryggja öryggi og heilleika.
  • Ensure proper gain staging; avoid setting input levels too high, which can cause clipping and distortion.
  • Try using a different USB port, preferably one directly on your computer's motherboard rather than a hub.
  • Keep the interface away from other electronic devices that might cause interference.
• Interface Disconnects on Mac Sleep:
  • This can be a known behavior with some Mac systems. Try adjusting your Mac's energy saver settings to prevent USB ports from sleeping.
  • If the issue persists, you may need to unplug and re-plug the USB cable, and re-select the interface in your DAW's preferences after your Mac wakes up.
• Phantom Power vandamál:
  • Ensure the microphone is properly connected before engaging phantom power.
  • Verify the microphone itself is functional and requires +48V phantom power.

Tæknilýsing

Ábyrgð og stuðningur

For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official Tascam webÞar finnur þú ítarlegar upplýsingar um þjónustuver, algengar spurningar og upplýsingar um tengiliði fyrir þjónustuver.

Tascam Official Websíða: https://tascam.com/us/