Hertz HDP4 4-rása 1000W hámark D-flokks Amplíflegri notendahandbók

1. Inngangur

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Hertz HDP4 4-Channel 1000W Max D-Class Amplifier. Please read this manual thoroughly before attempting installation or operation to ensure proper function and safety.

Mynd 1.1: Ofan frá og niður hallandi view of the Hertz HDP4 ampbjargvættur, sýningasing þess er samningur svartur casing and control panel on the top surface. The Hertz logo is visible on the main body.

2. Öryggisupplýsingar

Fylgdu alltaf eftirfarandi öryggisráðstöfunum:

• Disconnect the vehicle's battery before any installation or wiring.
• Gakktu úr skugga um að allar raflögn séu rétt einangraðar til að koma í veg fyrir skammhlaup.
• Settu upp amplifier securely in a well-ventilated area, away from moisture and direct heat.
• Notið viðeigandi raflögn fyrir aflgjafa og jarðtengingar eins og tilgreint er í uppsetningarkaflanum.
• Ráðfærðu þig við fagmann í uppsetningarferlinu ef þú ert óviss um einhvern hluta uppsetningarferlisins.

3. Innihald pakka

Gakktu úr skugga um að allir hlutir séu til staðar í pakkanum:

• Hertz HDP4 Amplifier Eining
• Festingarbúnaður (skrúfur, sviga)
• Notendahandbók (þetta skjal)

4. Uppsetning og uppsetning

4.1 Uppsetning Amplíflegri

Choose a suitable location for mounting the amplifier. It should be a dry, well-ventilated area, protected from direct sunlight and excessive vibration. Ensure there is sufficient space around the amplyftara fyrir loftflæði.

Mynd 4.1: Efst view of the Hertz HDP4 amplifier, illustrating its compact design and potential mounting points. The amplifier features a textured black finish with the Hertz logo prominently displayed.

1. Settu amplifier in the desired mounting location and mark the screw holes.
2. Drill pilot holes if necessary, ensuring not to damage any vehicle components.
3. Tryggðu þér amplyftaranum með meðfylgjandi festingarskrúfum.

4.2 Raflagnatengingar

Proper wiring is critical for performance and safety. Refer to the diagram below for power, ground, remote, and speaker connections.

Figure 4.2: Rear panel of the Hertz HDP4 amplifier, detailing the power input (BATT), ground (GND), remote turn-on (REM) terminals, and speaker output terminals (L/R mono for channels A and B). Two 40A fuses are also visible.

• Afl (rafhlaða): Connect a fused power cable (minimum 8 AWG recommended) directly from the vehicle's positive battery terminal to the BATT terminal on the amplíflegri.
• Jörð (GND): Connect a ground cable of the same gauge as the power cable from the GND terminal to a clean, unpainted metal point on the vehicle chassis.
• Fjarlægt (REM): Connect a remote turn-on wire from your head unit's remote output to the REM terminal.
• Útgangur hátalara: Connect your speakers to the appropriate L (left) and R (right) terminals for each channel (A and B). Ensure correct polarity. The amplifier supports mono bridging for increased power output to a single speaker or subwoofer.
• Öryggi: The amplifier is equipped with two 40A fuses. Replace only with fuses of the same type and rating.

4.3 Input Connections and Controls

The amplifier offers both RCA (low-level) and High-Level inputs, along with various crossover and gain controls.

Figure 4.3: Input and control panel of the Hertz HDP4 amplifier. This panel includes RCA pre-inputs (A PRE-IN, B PRE-IN), high-level inputs (A HI-IN, B HI-IN), and various adjustment knobs for levels, pass mode, and crossover settings. A switch for HI-IN AUTO TURN-ON is also present.

• RCA Pre-Inputs (A PRE-IN, B PRE-IN): Connect your head unit's RCA outputs to these inputs for low-level signal.
• High-Level Inputs (A HI-IN, B HI-IN): If your head unit does not have RCA outputs, connect speaker-level signals directly to these inputs. The amplifier features an auto turn-on function for high-level inputs.
• Stig: Adjust the input sensitivity (gain) to match the output of your head unit. Start with the gain at minimum and slowly increase until desired volume is achieved without distortion.
• Pass Mode: Select the desired crossover mode (e.g., Full, HPF, LPF) for each channel pair.
• Crossover Frequency (XOVER): Adjust the frequency point for the selected crossover mode.
• Margfaldari: Use this switch to multiply the crossover frequency setting by 1 or 10, depending on your system requirements.

5. Notkunarleiðbeiningar

5.1 Upphafsvirkjun

1. After all connections are made and verified, reconnect the vehicle's battery.
2. Kveiktu á höfuðtækinu. amplifier should power on automatically (if remote wire is connected or HI-IN AUTO TURN-ON is active).
3. Start with the head unit volume low and gradually increase it, listening for clear audio.

5.2 Að stilla hljóðstillingar

Fínstilla amplifier's settings for optimal sound quality:

• Gain Matching: Stilltu amplifier's gain controls (LEVELS) to match the output voltage of your head unit. This is crucial to prevent distortion.
• Crossover stillingar: Set the crossover frequencies (XOVER) and pass modes (PASS MODE) according to the specifications of your speakers. For full-range speakers, a high-pass filter (HPF) is often used to protect them from low bass frequencies. For subwoofers, a low-pass filter (LPF) is used.

6. Viðhald

To ensure the longevity and optimal performance of your Hertz HDP4 ampLifier, fylgdu þessum viðhaldsleiðbeiningum:

• Þrif: Hreinsaðu reglulega ampÞurrkið ytra byrði tækisins með mjúkum, þurrum klút. Notið ekki sterk efni eða slípiefni.
• Loftræsting: Gakktu úr skugga um að ampKælifingar liftarans eru lausar við ryk og hindranir til að viðhalda réttri varmaleiðni.
• Tengingar: Regularly check all wiring connections for tightness and corrosion. Loose connections can lead to poor performance or damage.
• Öryggi: If a fuse blows, replace it only with a fuse of the exact same type and rating (2 x 40A). Using an incorrect fuse can cause severe damage to the amplifier or vehicle electrical system.

Figure 6.1: Bottom panel of the Hertz HDP4 amplifier, displaying the serial number label and important caution notes regarding insulated screws. This area should be kept clean and free from obstructions.

7. Bilanagreining

Ef þú lendir í vandræðum með þinn ampLifier, skoðaðu eftirfarandi töflu áður en þú hefur samband við þjónustuver:

8. Tæknilýsing

Technical specifications for the Hertz HDP4 4-Channel 1000W Max D-Class Amplíflegri:

• Gerð: HDP4
• Vörumerki: HERTZ
• Tegund: 4-Channel D-Class Amplíflegri
• Hámarksafl: 1000W (as per product title, specific RMS not provided in data)
• Vörumál (L x B x H): 11.18 x 6.73 x 1.83 tommur
• Þyngd: 6.35 pund
• Voltage: 14.4 volt (í notkun)
• Gerð festingar: Yfirborðsfesting
• Öryggi: 2 x 40A
• ASIN: B00AWBU1FQ

9. Upplýsingar um ábyrgð

Hertz products are designed and manufactured to the highest quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Hertz webGeymið kaupkvittunina sem sönnun fyrir kaup vegna ábyrgðarkröfu.

10. Stuðningur

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Hertz customer support through their official website or authorized dealer. Ensure you have your product model (HDP4) and serial number ready when contacting support.

Official Hertz Websíða: www.hertzaudiovideo.com