SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. Inngangur

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

Mynd 1.1: Framan view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. Öryggisupplýsingar

• Lesið allar leiðbeiningar vandlega fyrir uppsetningu og notkun.
• Gakktu úr skugga um að aflgjafinn voltage matches the device's requirements (85-265V AC, 50/60Hz).
• Öll raflögn ætti að vera framkvæmd af löggiltum rafvirkja til að koma í veg fyrir rafstuð eða skemmdir á tækinu.
• Ekki nota tækið í umhverfi með miklum raka, ryki eða ætandi lofttegundum.
• Aftengdu rafmagnið áður en viðhald eða breytingar á raflögnum eru framkvæmdar.
• Keep the device away from strong electromagnetic interference.

3. Vörueiginleikar

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Breitt hitastigssvið fyrir rekstur.
• Compact and easy-to-install design.

4. Innihald pakka

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• 1 x Notendahandbók (þetta skjal)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. Uppsetning

5.1 Uppsetning

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2 Raflögn

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Flugstöðvar 1 og 2: AC Power Supply (85-265V AC, 50/60Hz)
• Flugstöðvar 3 og 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Flugstöðvar 6 og 7: Alarm Output (ALM) - Relay contacts for alarm.
• Flugstöðvar 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Flugstöðvar 11 og 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. Notkunarleiðbeiningar

6.1 Skjár lokiðview

The meter features a dual display:

• PV (ferlisgildi): The upper red display shows the current measured temperature/humidity.
• SV (Stillt gildi): The lower green display shows the desired set point.
• OUT vísir: Illuminates when the main output is active.
• AT vísir: Illuminates when the auto-tuning function is active.
• AL1/AL2 vísar: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 Hnappar aðgerðir

• SET hnappur: Notað til að fara í stillingarham fyrir færibreytur og staðfesta val.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (Niður) hnappur: Decreases the value of a parameter or set point.
• ▲ (Upp) hnappur: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. Í venjulegum rekstrarham, ýttu á SETJA button once. The SV display will begin to flash.
2. Notaðu ▲ (Upp) og ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. Ýttu á SETJA button again to confirm the new SV and exit the setting mode.

6.4 Ítarlegar breytustillingar

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the SETJA button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (Upp) og ▼ (Down) buttons to navigate through parameters and the SETJA button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7. Viðhald

• Þrif: Þurrkaðu af skjánum og casinÞurrkið með mjúkum, þurrum klút. Notið ekki slípiefni eða leysiefni.
• Skoðun: Athugið reglulega hvort raflögn séu laus eða tærð.
• Geymsla: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

8. Bilanagreining

9. Tæknilýsing

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. Ábyrgð og stuðningur

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER websíða fyrir upplýsingar um tengiliði.