ACT Dual Hard Drive Docking Station

Inngangur

The ACT AC1504 Dual Hard Drive Docking Station provides a convenient and efficient solution for connecting and accessing 2.5-inch and 3.5-inch SATA I/II/III hard drives and SSDs. This device supports high-speed data transfer via USB 3.0 (USB 3.2 Gen1) and features an offline cloning function, allowing you to duplicate drives without a computer connection. It is designed for data transfer, storage expansion, file backup, data recovery, system upgrades, and disk cloning.

Innihald pakka

Vinsamlegast staðfestu að allir hlutir séu í pakkanum þínum:

• ACT Dual Hard Drive Docking Station (AC1504)
• USB 3.0 Type-A to Type-B Cable
• Rafmagns millistykki
• Notendahandbók (þetta skjal)

Image: The ACT AC1504 Dual Hard Drive Docking Station, its power adapter, and the USB 3.0 cable, as included in the package.

Eiginleikar vöru

• Dual Bay Compatibility: Supports all 2.5-inch and 3.5-inch SATA I/II/III HDDs and SSDs up to 12.5mm thickness.
• Háhraða USB 3.0: Utilizes USB 3.2 Gen1 technology for ultra-fast data transfer rates up to 5 Gbps.
• UASP stuðningur: Enhanced performance with USB Attached SCSI Protocol.
• Offline Cloning: Clone data from one hard drive to another without requiring a computer connection.
• Fjölhæf notkun: Ideal for data transfer, storage expansion, file backup, data recovery, system upgrades, and disk cloning.

Uppsetning

1. Tengdu rafmagn: Plug the power adapter into the DC input port on the rear of the docking station. Connect the other end of the power adapter to a wall outlet.
2. Settu inn harða diska: Gently slide your 2.5-inch or 3.5-inch SATA HDD/SSD into the drive slots. Ensure the drives are fully seated. For offline cloning, the source drive should be in the 'Source' slot and the target drive in the 'Target' slot.
3. Connect to Computer (for data access): If you intend to use the docking station for data access via your computer, connect the USB 3.0 cable from the docking station's USB port to an available USB port on your computer.
4. Kveikt á: Flip the ON/OFF switch on the rear of the docking station to the 'ON' position. The power indicator LED will illuminate.

Image: Rear panel of the docking station, illustrating the USB 3.0 port, ON/OFF power switch, and DC power input for connections.

Image: The docking station connected to a laptop via its USB cable, with two hard drives inserted, demonstrating a typical setup for data access.

Notkunarleiðbeiningar

A. Data Access Mode (Connected to Computer)

1. Gakktu úr skugga um að tengikvíin sé kveikt á og tengd við tölvuna þína með USB 3.0 snúru.
2. Insert one or two SATA HDDs/SSDs into the available slots.
3. Stýrikerfið þitt ætti að greina diskana sjálfkrafa. Þeir munu birtast sem færanlegir geymslumiðlar.
4. You can now access, transfer, and manage files on the inserted drives as you would with any other external storage.

B. Offline Cloning Function

The offline cloning function allows you to duplicate a source drive to a target drive without a computer connection.

1. Undirbúa diska: Ensure both the source drive (the drive you want to copy FROM) and the target drive (the drive you want to copy TO) are SATA HDDs/SSDs. The target drive must be equal to or larger in capacity than the source drive.
2. Settu inn drif: Insert the source drive into the 'Source' slot (HDD1) and the target drive into the 'Target' slot (HDD2).
3. Aftengjast tölvu: Ensure the docking station is NOT connected to any computer via USB.
4. Kveikt á: Turn on the docking station using the ON/OFF switch.
5. Hefja klónun: Press and hold the 'Clone' button for approximately 3-5 seconds until the cloning progress LEDs (25%, 50%, 75%, 100%) begin to flash.
6. Staðfesta klónun: Release the button, then quickly press it again to confirm the cloning process. The cloning process will begin, indicated by the progress LEDs lighting up sequentially.
7. Fylgjast með framvindu: The LEDs will indicate the cloning progress (25%, 50%, 75%, 100%). All LEDs will remain solid when the cloning process is complete.
8. Slökkva á: Once cloning is complete, turn off the docking station and safely remove the drives.

Mikilvægt: All data on the target drive will be erased during the cloning process. Back up any important data from the target drive before initiating cloning.

Image: The ACT AC1504 Dual Hard Drive Docking Station with two hard drives inserted, illustrating its dual-bay design and the LED indicators for power, activity, and cloning progress.

Viðhald

• Haltu tengikvíinni hreinni og ryklausri. Notaðu mjúkan, þurran klút til að þrífa.
• Forðastu að útsetja tækið fyrir miklum hita, raka eða beinu sólarljósi.
• Reynið ekki að taka tækið í sundur eða gera við það sjálfur. Leitið til hæfs þjónustuaðila.
• Always power off the docking station before inserting or removing drives, especially during data transfer, to prevent data corruption.

Úrræðaleit

• Drif ekki greint:
  • Ensure the docking station is powered on and the drive is properly seated in the slot.
  • Verify the USB cable is securely connected to both the docking station and your computer.
  • Prófaðu að tengja við aðra USB tengi á tölvunni þinni.
  • Check if the drive is initialized and formatted in your computer's Disk Management (Windows) or Disk Utility (macOS).
• Hæg gagnaflutningur:
  • Gakktu úr skugga um að þú sért tengdur við USB 3.0 tengi á tölvunni þinni. USB 2.0 tengi munu leiða til hægari hraða.
  • Staðfestu að stýrikerfið þitt og reklar styðji USB 3.0 og UASP.
• Klónun án nettengingar mistekst eða byrjar ekki:
  • Ensure the docking station is NOT connected to a computer via USB during cloning.
  • Confirm the target drive's capacity is equal to or larger than the source drive's capacity.
  • Make sure both drives are properly inserted and detected by the docking station (power and activity LEDs should be on).
  • Follow the cloning steps precisely, especially the press-and-hold and quick-press sequence for the 'Clone' button.

Tæknilýsing

Ábyrgð og stuðningur

ACT provides reliable connectivity solutions. All ACT products comply with international standards and EU legislation. This product benefits from a factory warranty of 2 to 5 years.

For technical support or warranty claims, please refer to the official ACT websíðuna eða hafið samband við næsta söluaðila.

Websíða: www.act-connectivity.com