Notendahandbók fyrir Jaycar Digitech QC1938 100MHz stafrænan sveiflusjá

1. Inngangur

This manual provides detailed instructions for the safe and effective operation of your Jaycar Digitech QC1938 100MHz Digital Oscilloscope. Please read this manual thoroughly before using the device to ensure proper setup, operation, and maintenance. Retain this manual for future reference.

2. Öryggisupplýsingar

Observe the following safety precautions to prevent injury and avoid damage to the instrument or any products connected to it.

• Aflgjafi: Connect the oscilloscope only to the power source specified in this manual.
• Jarðtenging: Gakktu úr skugga um að tækið sé rétt jarðtengt til að koma í veg fyrir rafstuð.
• Rannsóknir: Use only probes supplied or recommended by the manufacturer. Ensure probes are rated for the voltage verið að mæla.
• Loftræsting: Ekki loka loftræstiopum. Tryggið nægilegt loftflæði í kringum tækið.
• Umhverfi: Operate the oscilloscope in a dry environment. Avoid exposure to moisture, dust, or extreme temperatures.
• Þjónusta: Refer all servicing to qualified service personnel. Do not attempt to repair the instrument yourself.

3. Innihald pakka

Gakktu úr skugga um að allir hlutir sem taldir eru upp hér að neðan séu til staðar í pakkanum þínum:

• Jaycar Digitech QC1938 Digital Oscilloscope
• 10:1 Passive Probe with 1.5m lead
• 2 x BNC to Clip Test Leads
• USB snúru
• Kraftleiðsla
• Notendahandbók (þetta skjal)

4. Vöru lokiðview

The Jaycar Digitech QC1938 is a 100MHz Digital Oscilloscope designed for precise electronic measurements. It features a 7-inch color LCD screen, two independent channels, and a built-in waveform generator.

Helstu eiginleikar:

• 7-inch TFT color LCD screen with 800 x 480 pixel resolution
• Two independent input channels
• 100MHz bandwidth and 1GSa/s samplanggengi
• 8M memory depth (single channel)
• Integrated 25MHz waveform generator (Sine, Square, Ramp, Exponential, Noise, DC)
• Auto scale function for automatic sine and square wave detection
• 14 trigger modes including Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, and IIC
• 5 serial protocol triggers and decodes: RS232/UART, I2C, SPI, CAN, and LIN
• Two 3-digit digital voltmeters and a 6-digit hardware frequency indicator
• 32 types of auto measurements with real-time statistics
• USB Host/Device interface for computer control and data storage

5. Uppsetning

5.1 Rafmagnstenging

1. Connect the supplied power lead to the power input on the rear panel of the oscilloscope.
2. Plug the other end of the power lead into a grounded AC power outlet.
3. Press the power button on the front panel to turn on the oscilloscope.

5.2 Kannatenging

1. Connect the BNC connector of the passive probe to either Channel 1 (CH1) or Channel 2 (CH2) input on the front panel.
2. Attach the ground clip of the probe to the circuit's ground point.
3. Connect the probe tip to the test point in your circuit.
4. Ensure the probe's attenuation setting (e.g., 1X or 10X) matches the setting on the oscilloscope for accurate readings.

6. Notkunarleiðbeiningar

6.1 Grunnaðgerð

• Auto Scale: Press the 'AUTO SET' button to automatically adjust vertical, horizontal, and trigger settings for a stable waveform display. This function detects sine and square waves automatically.
• Vertical Controls (VOLTS/DIV, POSITION): Use the VOLTS/DIV knobs to adjust the vertical scale (voltage per division) for each channel. The POSITION knobs shift the waveform vertically.
• Horizontal Controls (SEC/DIV, POSITION): Use the SEC/DIV knob to adjust the horizontal scale (time per division). The horizontal POSITION knob shifts the waveform horizontally.
• Kveikjastig: Adjust the 'TRIGGER LEVEL' knob to set the voltage level at which the oscilloscope captures a waveform.

6.2 Ítarlegar aðgerðir

• Bylgjuform rafall: Access the waveform generator menu to select and configure output waveforms such as Sine, Square, Ramp, Exponential, Noise, and DC. Connect the 'WAVE GEN' output to your circuit.
• Kveikjastillingar: Utilize the 14 available trigger modes (Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC) to capture specific events. Select modes via the 'TRIGGER' menu.
• Serial Protocol Decoding: The oscilloscope supports decoding for RS232/UART, I2C, SPI, CAN, and LIN protocols. Configure these settings in the 'DECODE' menu to view decoded data.
• Mælingar: The device offers 32 types of automatic measurements with real-time statistics (maximum, minimum, standard deviation, etc.). Access these via the 'MEASURE' menu.
• USB tenging: Connect a USB thumb drive to the USB Host port to save oscilloscope setups, waveforms, reference waveforms, CSV files, and images. The USB Device port allows for remote control from a computer using SCPI commands.

7. Viðhald

7.1 Þrif

To clean the instrument, use a soft cloth dampened with a mild detergent solution. Do not use abrasive cleaners or solvents that could damage the casing eða skjár. Gakktu úr skugga um að tækið sé slökkt og aftengt áður en það er þrifið.

7.2 Geymsla

When not in use, store the oscilloscope in a dry, dust-free environment away from direct sunlight and extreme temperatures. Use the original packaging or a suitable case for protection during transport.

8. Bilanagreining

If you encounter issues with your oscilloscope, refer to the following common problems and solutions:

Ef vandamálið heldur áfram eftir að þessar lausnir hafa verið prófaðar, vinsamlegast hafið samband við þjónustuver.

9. Tæknilýsing

10. Ábyrgð og stuðningur

Til að fá upplýsingar um ábyrgð og tæknilega aðstoð, vinsamlegast skoðið fylgiskjölin sem fylgdu með kaupunum eða hafið samband við söluaðila. Geymið kaupkvittunina vegna ábyrgðarkröfu.