Boardcon Embedded CM1126B-P System on Module
Tæknilýsing
| Eiginleiki | Tæknilýsing |
| CPU | Fjórkjarna Cortex-A53 |
| DDR | 2GB LPDDR4 (allt að 4GB) |
| eMMC FLASH | 8GB (allt að 256GB) |
| Kraftur | DC 3.3V |
| MIPI DSI | 4-braut |
| I2S | 4-CH |
| MIPI CSI | 2-CH 4-braut |
| RGB LCD | 24 bita |
| Myndavél | 1-CH(DVP) og 2-CH(CSI) |
| USB | 2-CH (USB HOST 2.0 and OTG 2.0) |
| Ethernet | 1000M GMAC |
| SDMMC | 2-CH |
| I2C | 5-CH |
| SPI | 2-CH |
| UART | 5-CH, 1-CH(KEILA) |
| PWM | 11-CH |
| ADC IN | 4-CH |
| Stærð víddar | 34 x 35 mm |
Inngangur
Um þessa handbók
Þessari handbók er ætlað að veita notandanum yfirview of the board and its benefits, complete feature specifications, and setup procedures. It contains important safety information as well.
Endurgjöf og uppfærsla á þessari handbók
Til að hjálpa viðskiptavinum okkar að nýta vörur okkar sem best erum við stöðugt að gera viðbótar og uppfært úrræði aðgengilegt á Boardcon webvefsvæði (www.boardcon.com, www.armdesigner.com). Þar á meðal eru handbækur, umsóknarskýrslur, forritun tdamples, og uppfærður hugbúnaður og vélbúnaður. Kíktu reglulega inn til að sjá hvað er nýtt! Þegar við erum að forgangsraða vinnu á þessum uppfærðu auðlindum eru endurgjöf frá viðskiptavinum númer eitt sem hefur áhrif. Ef þú hefur spurningar, athugasemdir eða áhyggjur af vörunni þinni eða verkefni skaltu ekki hika við að hafa samband við okkur á support@armdesigner.com.
CM1126B-P Introduction
Samantekt
The CM1126B-P system-on-module is equipped with Rockchip’s RV1126B-P, built with a quad-core Cortex-A53, 3.0 TOPs NPU, and RISC-V MCU. It is designed specifically for the IPC/CVR devices, AI Camera devices, intelligent interactive devices, and mini robots. High-performance and low-power solutions can help customers introduce new technologies more quickly and enhance the overall solution efficiency. The smallest size can be put on a 38board. Following the hardware revision from CM1126 (V1) to CM1126B-P (V2), where the SoC is updated to the RV1126B-P, the Reset & OTG_VBUS signals and the WIFI/BT module’s GPIO voltage must operate at a 3.3V logic level.
Eiginleikar
Örgjörvi
- Fjórkjarna Cortex-A53 allt að 1.6GHz
- 32KB I-skyndiminni og 32KB D-skyndiminni fyrir hvern kjarna, 512KB L3 skyndiminni
- 3.0 TOPS taugaferliseining
- RISC-V MCU to support 250ms fast boot
- Hámark 12M ISP
Minnisstofnun
- LPDDR4 vinnsluminni allt að 4GB
- eMMC allt að 256GB
- SPI Flash allt að 8MB
Vídeóafkóðari/kóðari
- Styður myndbandsafkóðun/kóðun allt að 4K@30fps
- Styður rauntíma umkóðun H.264/265
- Styður rauntíma UHD H.264/265 myndkóðun
- Myndastærð allt að 8192×8192
Sýna undirkerfi
- Myndbandsúttak
- Styður 4 brautir MIPI DSI allt að 2560×1440@60fps
- Supports 24-bit RGB parallel output
- Mynd í
- Supports up to 16-bit DVP interface
- Styður 2ch MIPI CSI 4lanes tengi
I2S/PCM/AC97
- Þrjú I2S/PCM tengi
- Styðja Mic array Allt að 8ch PDM/TDM tengi
- Styður PWM hljóðúttak
USB og PCIE
- Tvö 2.0 USB tengi
- One USB 2.0 OTG and one 2.0 USB host
Ethernet
- RTL8211F um borð
- Stuðningur 10/100/1000M
I2C
- Allt að fimm I2C
- Styðja staðlaða stillingu og hraðvirka stillingu (allt að 400kbit/s)
SDIO
- Styðja 2CH SDIO 3.0 samskiptareglur
SPI
- Allt að tveir SPI stýringar,
- Fullt tvíhliða samstillt raðviðmót
UART
- Styðja allt að 6 UART
- UART2 með 2 vírum fyrir kembiverkfæri
- Embedded two 664-byte FIFOs
- Styðja sjálfvirka flæðisstýringu fyrir UART0/1/3/4/5
ADC
- Allt að fjórar ADC rásir
- 12 bita upplausn
- Voltage inntakssvið á milli 0V til 1.8V
- Styður allt að 1MS/ssamplanggengi
PWM
- 11 á-flís PWMs með truflun-undirstaða aðgerð
- Support 32-bit time/counter facility
- IR valkostur á PWM3/7
Afltæki
- Discrete Power um borð
- Eitt 3.3V inntak
CM1126B-P Block Diagram
RV1126B-P Block Diagram
Development board (Idea1126) Block Diagram
CM1126B-P PCB Dimension
CM1126B-P Pin Definition
| Pinna | Merki | Lýsing eða aðgerðir | GPIO raðnúmer | IO binditage |
| 1 | LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | LCDC_D20_3V3 | I2S1_SDO_M2/CIF_VS_M1 | GPIO2_D0_d | 3.3V |
| 3 | LCDC_D21_3V3 | I2S1_SCLK_M2/CIF_CLKO_M1 | GPIO2_D1_d | 3.3V |
| 4 | LCDC_D22_3V3 | I2S1_LRCK_M2/CIF_CKIN_M1 | GPIO2_D2_d | 3.3V |
| 5 | LCDC_D23_3V3 | I2S1_SDI_M2/CIF_HS_M1 | GPIO2_D3_d | 3.3V |
| 6 | GND | Jarðvegur | 0V | |
| 7 | GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | GPIO1_D1_d | 3.3V(V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V(V2) |
| 9 | WIFI_REG_ON | SPI0_MOSI_M0 | GPIO0_A6_d | 3.3V(V2) |
| 10 | BT_RST | SPI0_MISO_M0 | GPIO0_A7_d | 3.3V(V2) |
| 11 | WIFI_WAKE_HOST | SPI0_CLK_M0 | GPIO0_B0_d | 3.3V(V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V(V2) |
| 13 | PWM7_IR_M0_3V3 | GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | Fyrir villuleit | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | Fyrir villuleit | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
GPIO3_D5_d | 3.3V |
| Pinna | Merki | Lýsing eða aðgerðir | GPIO raðnúmer | IO binditage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Jarðvegur | 0V | |
| 32 | OTG_DP | Can be used for download | 1.8V | |
| 33 | OTG_DM | Can be used for download | 1.8V | |
| 34 | OTG_DET(V2) | OTG VBUS DET IN | 3.3V(V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | 3.3V Main Power inntak | 3.3V | |
| 38 | VCC3V3_SYS | 3.3V Main Power inntak | 3.3V | |
| 39 | USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | Verður að nota fyrir SD kort | GPIO0_A3_u | 3.3V(V2) |
| 41 | CLKO_32K | RTC klukka framleiðsla | GPIO0_A2_u | 3.3V(V2) |
| 42 | nÚRSTILLA | Endurstilla lykilinntak | 3.3V(V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
MIPI CSI0 eða LVDS0 inntak | 1.8V |
| Pinna | Merki | Lýsing eða aðgerðir | GPIO raðnúmer | IO binditage |
| 52 | MIPI_CSI_RX0_D0
N |
MIPI CSI0 eða LVDS0 inntak | 1.8V | |
| 53 | GND | Jarðvegur | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
MIPI CSI1 eða LVDS1 inntak | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Jarðvegur | 0V | |
| 71 | LED1/CFG_LDO0 | Ethernet LINK LED | 3.3V | |
| 72 | LED2/CFG_LDO1 | Ethernet SPEED LED | 3.3V | |
| 73 | MDI0 + | Ethernet MDI merki | 1.8V | |
| 74 | MDI0- | Ethernet MDI merki | 1.8V | |
| 75 | MDI1 + | Ethernet MDI merki | 1.8V | |
| 76 | MDI1- | Ethernet MDI merki | 1.8V | |
| 77 | MDI2 + | Ethernet MDI merki | 1.8V | |
| 78 | MDI2- | Ethernet MDI merki | 1.8V | |
| 79 | MDI3 + | Ethernet MDI merki | 1.8V | |
| 80 | MDI3- | Ethernet MDI merki | 1.8V | |
| 81 | I2C1_SCL | UART4_CTSn_M2 | GPIO1_D3_u | 1.8V |
| Pinna | Merki | Lýsing eða aðgerðir | GPIO raðnúmer | IO binditage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | GPIO2_A3_d | 1.8V |
| 90 | GND | Jarðvegur | 0V | |
| 91 | LCDC_D0_3V3 | UART4_RTSn_M1/CIF_D0_M1 | GPIO2_A4_d | 3.3V |
| 92 | LCDC_D1_3V3 | UART4_CTSn_M1/CIF_D1_M1 | GPIO2_A5_d | 3.3V |
| 93 | LCDC_D2_3V3 | UART4_TX_M1/CIF_D2_M1 | GPIO2_A6_d | 3.3V |
| 94 | LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | GPIO2_A7_d | 3.3V |
| 95 | LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | GPIO2_B0_d | 3.3V |
| 96 | LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | GPIO2_B1_d | 3.3V |
| 97 | LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
GPIO2_B2_d | 3.3V |
| 98 | LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1/CIF_D3_M1 |
GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
GPIO2_D7_d | 3.3V |
| 102 | LCDC_VSYNC_3V3 | UART3_RTSn_M2/SPI1_MOSI | GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCIN3 | ADC inntak | 1.8V | |
| 114 | ADCIN2 | ADC inntak | 1.8V | |
| 115 | ADCIN1 | ADC inntak | 1.8V | |
| 116 | ADKEY_IN0 | Endurheimtarstilling (10K PU) | 1.8V | |
| 117 | GND | Jarðvegur | 0V | |
| 118 | SDIO_CLK | GPIO1_B2_d | 3.3V(V2) | |
| 119 | SDIO_CMD | GPIO1_B3_u | 3.3V(V2) |
| Pinna | Merki | Lýsing eða aðgerðir | GPIO raðnúmer | IO binditage |
| 120 | SDIO_D0 | GPIO1_B4_u | 3.3V(V2) | |
| 121 | SDIO_D1 | GPIO1_B5_u | 3.3V(V2) | |
| 122 | SDIO_D2 | GPIO1_B6_u | 3.3V(V2) | |
| 123 | SDIO_D3 | GPIO1_B7_u | 3.3V(V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V(V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V(V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V(V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V(V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V(V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V(V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V(V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V(V2) |
| 132 | LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | GPIO2_D4_d | 3.3V |
| 137 | LCDC_D10_3V3 | CIF_D6_M1 | GPIO2_B6_d | 3.3V |
| 138 | LCDC_D9_3V3 | CIF_D5_M1 | GPIO2_B5_d | 3.3V |
| 139 | LCDC_D8_3V3 | CIF_D4_M1 | GPIO2_B4_d | 3.3V |
| 140 | LCDC_D11_3V3 | CIF_D7_M1 | GPIO2_B7_d | 3.3V |
| 141 | LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | GPIO2_D5_d | 3.3V |
| 142 | LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Athugið:
1. Flest GPIO binditage er 1.8V, en nokkrir pinnar merktir 3.3V. 2. GPIO voltage change to 3.3V for marked (V2). |
||||
Development Kit (Idea1126)
Vélbúnaðarhönnunarleiðbeiningar
Tilvísun útlægra hringrásar
Aðalrafrás
Villuleit hringrás
USB OTG tengi hringrás
PCB fótspor
Rafmagns einkenni vöru
Útbreiðsla og hitastig
| Tákn | Parameter | Min | Týp | Hámark | Eining |
| VCC3V3_SYS | Kerfi IO
Voltage |
3.3-5% | 3.3 | 3.3 + 5% | V |
| Isys_in | VCC3V3_SYS inntak Núverandi | 850 | mA | ||
| Ta | Rekstrarhitastig | -20 | 70 | °C | |
| Tstg | Geymsluhitastig | -40 | 85 | °C |
Áreiðanleiki prófs
| Rekstrarpróf fyrir háan hita | ||
| Innihald | Operating 8h in high temperatures | 55 ° C ± 2 ° C |
| Niðurstaða | TBD |
| Rekstrarlífspróf | ||
| Innihald | Operating in the room | 120 klst |
| Niðurstaða | TBD |
Takmörkuð ábyrgð
Boardcon warrants this product to be free of defects in material and workmanship for one year from the date of purchase. During this warranty period, Boardcon will repair or replace the defective unit by the following process: A copy of the original invoice must be included when returning the defective unit to Boardcon. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product. This warranty is limited to the repair or replacement of the defective unit. In no event shall Boardcon be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product. Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please contact Boardcon to arrange for any repair service and to obtain repair charge information.
Algengar spurningar
Q: How do I upgrade the DDR memory on CM1126B-P?
A: The CM1126B-P supports up to 4GB LPDDR4 memory. To upgrade, ensure compatibility with the specifications and follow recommended procedures.
Q: What is the power supply requirement for CM1126B-P?
A: The power requirement for CM1126B-P is DC 3.3V. Ensure to provide a stable power supply within this range for optimal performance.
Q: Can I expand the storage capacity of eMMC on CM1126B-P?
A: Yes, the eMMC storage on CM1126B-P can be expanded up to 256GB. Ensure compatibility with supported storage devices before upgrading.
Skjöl / auðlindir
 |
Boardcon Embedded CM1126B-P System on Module [pdfNotendahandbók V2.20250422, CM1126B-P System on Module, CM1126B-P, System on Module, Module |