FoxTech RDD-25 4 Channel Payload Release and Drop Device Module
Tæknilýsing
| Vörumál | 125mm x 117mm x 60mm |
| Vöruþyngd | 330g |
| Tegund viðmóts | SKYPORT V2 / E-PORT / Type-C |
| Eftirlitsaðferð | PSDK |
| Kerfisstyrkur | 20W |
| Rekstrarhitastig | -20°( til 60°( |
| Fjöldi rása | 4 |
|
Stjórnunarhamur |
Independent channel control; select any hook number or one-key all release |
| Control Range | Same as drone communication range |
| Staða viðbrögð | Real-time feedback for each channel |
| Uppsetningaraðferð | Quick-detach buckle |
| Supported Hub | Já |
| Burðargeta | 2.5kg per channel |
Innihald pakka
| Nafn | Magn | Eining |
| RDD-25 | 1 | Sett |
| Pökkunarbox | 1 | Sett |
| Payload Release Hook Rings | 12 | Stykki |
| Certificat e of Confor mit y | 1 | Stykki |
Understanding the 4-Channel Payload Release and Drop Device
Uppsetning tækis
Skref 1: Turn the drone upside down and remove the two screws at the bottom of the gimbal mount.
Skref 2: Confirm the connection position between the alloy bracket and the drone. To better fit the drone body, the bottom of the alloy bracket is slanted and one side has a groove. During installation, align the bottom of the alloy bracket with the drone body, and ensure the grooved side faces outward.
Skref 3: Insert one end of the alloy bracket into the middle of the connection point between the gimbal and the airframe, align the screw holes at both ends of the alloy bracket with the corresponding holes on the airframe, fasten the alloy bracket to the airframe at the gimbal-connection side using the supplied M3*10 screws, and fasten the other end using the supplied M3*8 screws.
Skref 4: Connect the mounting plate to the alloy bracket, with the cable outlet facing the nose of the aircraft; adjust the exact mounting position of the plate as needed for actual use, and fasten the mounting plate to the alloy bracket using the supplied M3*8 screws.
Skref 5: Connect the device power pickup to the mounting plate power port; ensure the groove on the power pickup aligns with the power port, and after insertion confirm that both quick-release latches have fully popped out before normal use (depending on the purchased version, connect the mounting plate interface to the HUB or the aircraft E-PORT).
The mounting plate power port must be inserted aligning with the groove on the device power pickup
Skref 6: Insert the connector of the 4-Channel Payload Release and Drop Device into the corresponding E-PORT.
Connect the plugs as shown in the picture
Skref 7: As shown in the figure, manually press the hook control button to set the hook into standby release mode. After that, attach the matching metal ring to the payload and hang it on the hook.
Rekstur tækis
PSDK Button: Single click to open/close the 4-Channel Payload Release and Drop Device operation menu
Operation Button Description
Payload Control
Open the Payload settings; you can also operate the 4-Channel Payload Release and Drop Device through this menu (tap the menu icon in the upper-right corner of the remote controller 
to enter Payload settings).
Display real-time data switch: Show/Hide the working status and detailed information of the 4-Channel Payload Release and
Sleppa tæki
Single click to unlock/lock; after unlocking, the device can operate normally
Krókur 1: Single click to release
Hook 2: Single click to release
Hook 3: Single click to release
Hook 4: Single click to release
One-key all-release switch: Single click to release
Úrræðaleit
|
1 |
No PSDK control icon |
1. Check whether the wiring is correct. For the M350 version, plug into the top E-PORT of the aircraft and pay attention to the connector orientation. For the M300 version, connect to the supplied adapter ring and plug into the gimbal. For the visual version, connect the Type-C cable to the visual module and install the visual module on the gimbal.
2. Check the drone and remote controller firmware; they must be updated to the latest version. |
|
2 |
Incomplete PSDK icon display |
1. Close the Pilot2 flight app in the background and re-enter, or restart. 2. Check the drone and remote controller firmware; they must be updated to the latest version. |
Device External Interfaces
Vélbúnaðarviðmót: None for third-party hardware
Software Protocol Interfaces: Engin
Algengar spurningar
What is the maximum payload capacity of the RDD-25 system?
Each unit can carry a maximum of 2.5 kg, with a total system payload capacity of 10 kg.
What are some common applications of the RDD-25 device?
The RDD-25 device is suitable for tasks such as fire extinguisher deployment, emergency material delivery, power line stringing, and urgent rescue operations.
How many payload release units are included in the RDD-25 system?
The RDD-25 system consists of four individual payload release units that are triggered sequentially.
Skjöl / auðlindir
 |
FoxTech RDD-25 4 Channel Payload Release and Drop Device Module [pdfNotendahandbók RDD-25 4 Channel Payload Release and Drop Device Module, RDD-25, 4 Channel Payload Release and Drop Device Module, 4 Channel Payload Release and Drop Device Module, 4 Channel Payload Release, Payload Release and Drop Device Module |