CITADEL MESH
MIDI TOWER CASE
NOTANDA HANDBOÐ
Innihald
fela sig
INNIHALD FYLGIPAKKAR
Fjarlæging af spjöldum
FJÁRTAKA FRAMSÍÐA/HLIÐARHALDA
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
MÓÐABORÐIN INSTALLATION
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
UPPSETNING AFLAGI
UPPSETNING AFLAGI
- Place PSU in the bottom rear of the case, within the PSU shroud
- Stilltu götin og festu þau með skrúfum
UPPSETNING SKJÁMAKORT/PCI-E KORT
UPPSETNING SKJÁMAKORT/PCI-E KORT
- Fjarlægðu afturhliðar PCI-E raufa eftir þörfum (fer eftir raufarastærð kortsins þíns)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
2.5" SSD UPPSETNING (FRAMAN)
- Align your drive over the screw holes and secure with screws from the rear
2.5" SDD UPPSETNING (R)
2.5" SSD UPPSETNING (AFTAN)
Place your SSD on top of the HDD bracket and secure with screws
3.5" HDD UPPSETNING
3.5" HDD UPPSETNING
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
UPPSETNING VIÐVIFTA
UPPSETNING VIÐVIFTA
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
UPPSETNING FRAM/AFTA VIÐVIFTA
UPPSETNING FRAM/AFTA VIÐVIFTA
- Align your fan to the screw holes on the chassis and secure with screws
UPPSETNING VATNSKÆLI
UPPSETNING VATNSKÆLI
- Festið vifturnar við ofninn, festið síðan ofninn inni í undirvagninum með því að festa með skrúfum að utan
UPPSETNING I/O PÁLS
UPPSETNING I/O PÁLS
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Skjöl / auðlindir
 |
KOLINK ANL-INT Citadel Mesh Midi Tower kassa [pdfNotendahandbók ANL-INT, ANL-INT Citadel Mesh Midi Tower kassi, Citadel Mesh Midi Tower kassi, Mesh Midi Tower kassi, Midi Tower kassi, Tower kassi |