Vimark 4700ZT útsogsvifta, svæði 1, útsogsvifta með tímastilli

4700ZT	4” (100mm) Zone 1, Timer	4660P	6″ útsogsviftu-dragsnúra
4700ZTH	4” (100mm) Zone 1, Timer & Rakastöð	4661P	6″ útsogsviftu með tímastilli
4600P	4″ útsogsviftu-dragsnúra	4750S	4” (100mm) Inline Axial Fan
4601P	4″ útsogsviftu-dragsnúra Tímamælir	4751T	4” (100mm) Inline Axial Fan Timer
4720Z	4” Zone 1 Flat Fascia Extractor Fan	4720ZT	4” Zone 1 Flat Fascia Extractor Fan with Timer

Safety Instructions And Installation Notes

Öryggisleiðbeiningar

• Always switch off the electrical supply before commencing installation.
• This fan must be connected via a DP connection unit which is fitted with a 3A fuse.
• This fan must be installed using fixed wiring. A flexible cable should not be used.
• Connect to a 240V ac electrical supply. This extractor fan is double insulated and does not require an earth.
• Vinsamlegast athugaðu IP (Ingress Protection) einkunn þessarar vöru þegar þú ákveður staðsetningu fyrir uppsetningu.
• Tis product is class II double insulated
• This extractor fan must be installed in accordance with the current edition of the IET Wiring Regulations and Building Regulations, BS 7671.

Uppsetningarskýringar

• When installing this fan through an external wall, an external grille must be fitted at all times.
• The extractor fan must be mounted on flat surface.
• The extractor fan should be installed a minimum of 1.8m from the floor.
• For the best results, the extractor fan should be fitted as high as possible on the wall.

Ef þú ert í vafa skaltu hafa samband við viðurkenndan rafvirkja

Eiginleikar vöru

Timer Fans

Timer fans are designed to be connected to the lighting circuit so that they will operate when the light is switched on, and stay on for a pre-set time after the light has been switched off.

Timer and Humidistat Fans

Timer and Humidistat fans are designed to be connected to the lighting circuit and will operate when either the light is switched on or when the humidity level exceeds the pre-set level between 60 and 90%.

Þegar ljósið er slökkt eða rakastigið fer niður fyrir fyrirfram stillt gildi, mun viftan haldast í gangi í þann tíma sem stilltur er með tímastillinum, á bilinu 2-30 mínútur.

Hávaðastig

All ventilations fans have a low noise level, under 35dB.

Hitatrygging

All Vimark ventilation fans have a thermal fuse which prevents the motor overheating if the impeller becomes jams.

Uppsetningarleiðbeiningar

1. Slökktu á rafveitunni áður en byrjað er að setja hana upp.
2. Drill a hole in the wall to suit the fan and ducting: 4” fan Ø 110mm hole max.
   If mounting the fan on the ceiling, position the fan between the joists
3. Route ducting from the fan position to the external grille position, ensuring the end of the ducting is flush to the walls. Ducting runs should be as short as possible for optimum performance.
4. Remove the front cover of the fan by undoing the securing screw on the bottom edge. To access the cover on the Flat Facia fans remove the front plate first by pulling away from the pillars in each corner.
5. Hold the body of the fan in position and mark on the wall/ceiling the four fixing screw positions and the cable entry hole.
6. Drill and plug the wall/ceiling.
7. Route the cable so that it exits through the wall ceiling at the position marked, leaving enough cable protruding so it can be terminated.
8. Fix the fan body in position.
9. Terminate the cable. (For Zone 1 fan the internal cover must be removed to access the terminal block)
10. Fit the front cover and tighten the securing screw.
11. Kveiktu á og athugaðu hvort það virki rétt.

Afköst loftræstikerfis

Vimark ventilation fans are design to meet the requirements of The Building Regulations – Approved Document F1 Means of Ventilation, and The Building Standards (Scotland) – Domestic Ventilation.

Þessar byggingarreglugerðir og leiðbeiningar um eftirlit með byggingarþjónustu fyrir heimili kveða á um að slitrótt útsogsviftur skuli hafa sérstakt viftuafl (SPF) sem er minna en 0.5 W/(ltr/sek). Vimark-viftur uppfylla þessa kröfu.

Staðsetning viftu

Vimark loftræstiviftur eru hannaðar til að flytja loft yfir stuttar vegalengdir, yfirleitt undir 2 m, og henta fyrir uppsetningu í gegnum veggi. Þessar loftræstiviftur er einnig hægt að setja upp í loft með loftstokklengd undir 2 m.

Loftræstingarviftan ætti alltaf að vera staðsett í veggnum eða í loftinu, fjærst aðalloftgjafanum, t.d. hurð, til að tryggja bestu mögulegu afköst. Viftan ætti einnig að vera staðsett eins hátt uppi og mögulegt er.

Raflögn

Standard vifta
The standard fan can be connected to the lighting circuit and controlled from a switch so that it only operates when the switch is on. The fan must be fed by a DP switched connection unit fitted with a 3A fuse. Sjá mynd 1.

Tengingarnar fyrir þennan viftu eru:
L permanent live
N hlutlaus

Tímastillir og rakastillir
The timer fan can be connected to the lighting circuit. The circuit for this fan must be protected by a 3A device and should be controlled by a 3 pole fan isolator. Sjá mynd 2.

Tengingarnar fyrir þennan viftu eru:
L permanent live
S switch live
N hlutlaus

In-Line Axial fan
The In-Line Axial fan can be connected to the lighting circuit and controlled from a switch so that it only operates when the switch is on. The fan must be fed by a DP switched connection unit fitted with a 3A fuse. Sjá mynd 3.

Tengingarnar fyrir þennan viftu eru:
L permanent live
N hlutlaus
S or LT Switch Live

Stjórnastillingar

Tímastillirinn, rakastillirinn og tímastillirinn á viftunum fylgja einangraðir skrúfjárn sem eru fest við viftuhúsið og staðsett inni í viftunni til að stilla stjórntækin.

Tímamælir
The timer is adjustable from approximately 2 minutes to 30 minutes. The timer is factory set at approximately 15 minutes. Turn the control clockwise to increase the on time. Timers should be set for 15 minutes minimum.

Rakastöð
The humidistat range is approximately 60 – 90% relative humidity. The humidistat is factory set at approximately 75%. Turn the control clockwise to increase humidity.

Zone 1 Fans
To access the terminals and dials in the zone 1 fans remove the rubber cap on the right of the fan and the plastic terminal cover on the top left.
When dials are set to the required setting and the cables are securely terminated replace the cap/cover to maintain the IP rating.

Almennt

Þessa vöru ætti að endurvinna á réttan hátt þegar hún nær endalokum líftíma hennar. Athugaðu sveitarfélög um hvar aðstaða er til staðar.
Hreinsið aðeins með mjúkum þurrum klút, ekki nota árásargjarn hreinsiefni eða leysiefni sem geta skemmt vöruna.
This product has a 3 year warranty from the date of purchase.

Forskrift

Voltage	220 – 250V ac 50Hz	Extraction Rate Zone 1 Fan 4”	97m3 /hr (27 ltr/sec)
Stærð holuskurðar	Ø 110mm hole max.	Extraction Rate 4” Flat Fascia	85m3 /hr (23 ltr/sec)
Einangrunarflokkur	Flokkur II	Extraction Rate 4” inline Axial	137m3 /hr (38 ltr/sec)
Aðlögun tímastillingar	2 – 30 mínútur	IP einkunn	IP 44 (Svæði 1 vifta IP X4)
Humidistat Adjustment	60 – 90% raki	Fylgni	BS EN 60335-2-80

Þjónustudeild

Deta Electrical Company Limited
Bretland: Panattoni Park, Luton Road, Chalton, Bedfordshire, LU4 9TT
ESB: Unit 16 Ashbourne Ind. Est. Ashbourne, Co. Meath A84 W972 Ireland deta.co.uk Technical Helpline: +44 (0)1582 544 548

Skjöl / auðlindir

Vimark 4700ZT útsogsvifta, svæði 1, útsogsvifta með tímastilli [pdfUppsetningarleiðbeiningar 4700ZT, 4700ZTH, 4600P, 4601P, 4720Z, 4660P, 4661P, 4750S, 4751T, 4720ZT, 4700ZT Útsogsviftur Svæði 1 útsogsvifta með tímastilli, 4700ZT, Útsogsviftur Svæði 1 útsogsvifta með tímastilli, Svæði 1 útsogsvifta með tímastilli, Útsogsvifta með tímastilli, Vifta með tímastilli, með tímastilli

Heimildir

• Notendahandbók